YUEQING WINSTON ELECTRIC CO.,LTD.
Yueqing Winston Electric Co., Ltd Proximity sensor,switching power supply,voltage stabilizer,motor soft starter,frequency inverter,float switch,AC magnetic contactor, thermal overload relay, terminal
Add to Cart
120 Watt Switched Mode Power Supply 11A 5A Triple Output Low Operation Temperature
Description:
1 . Low price and high reliability
2 . 105°C Output capacitor
3 . AC input power suitable for the world
4 . High efficiency and low operation temperature
5 . 100% full-load burn-in test
6 . Installed with EMI filter,minimum wave
Specification:
| Model | T-120A | T-120B | T-120C | T-120D | ||||||||
| Specification | CH1 | CH2 | CH3 | CH1 | CH2 | CH3 | CH1 | CH2 | CH3 | CH1 | CH2 | CH3 |
| DC output voltage | 5V | 12V | -5V | 5V | 12V | -12V | 5V | 15V | -15V | 5V | 12V | 24V |
| Output voltage error(Note,2) | ±2% | ±5% | ±5% | ±2% | ±5% | ±5% | ±2% | ±5% | ±5% | ±2% | ±6% | ±6% |
| Rated output current | 3A | 2A | 0.5A | 3A | 2A | 0.5A | 3A | 1.5A | 0.5A | 3A | 1.5A | 0.5A |
| Output current rage | 0.6-7A | 0.2-1A | 0.2-1A | 0.6-5A | 0.2-1A | 0.2-1A | 0.6-4A | 0.2-1A | 0.2-1A | 0.6-4A | 0.2-1.2A | 0.2-1.2A |
| Wave and noise(Note ,3) | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV | 100mV |
| Inlet stability(Note ,4) | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±0.5% | ±1% |
| Load stablity (Note ,5) | ±1% | ±4% | ±4% | ±1% | ±4% | ±4% | ±1% | ±4% | ±4% | ±1% | ±5% | ±5% |
| DC output power | 52W | 49W | 50W | 51W | ||||||||
| Efficiency | 66% | 69% | 71% | 72% | ||||||||
| Adjustable range for DC voltage | CH1,+10,-5% | CH1,+10,-5% | CH1,+10,-5% | CH1,+10,-5% | ||||||||
| AC input voltage range | 85-132VAC/170-264VAC 47-63Hz,240-370VDC | |||||||||||
| Input current | 1.6A/115V 0.8A/230A | |||||||||||
| AC INnrush current | Cold-start current 20A/115V 40A/230V | |||||||||||
| Leakage current | <0.5mA/240VAC | |||||||||||
| Overload proctection | 105%-150%Type:Foldback,current limiting reset,auto recovery | |||||||||||
| Over-voltage protection | ………… | |||||||||||
| High-temperature protection | ………… | |||||||||||
| Temperature coefficient | ±0.03%/°C(0-50°C)ON+5V | |||||||||||
| Setup rise hold up time | 200ms,50ms,16ms | |||||||||||
| Vibration | 10-500Hz,2G 10min,/1cycle,Period for60min,Each axes | |||||||||||
| Withstand voltage | Input and output internal,1.5KVAC,Input and enclosure,1.5KVAC,Output and enclosure,0.5KVAC | |||||||||||
| Isolation resistance | Input and output internal,Input and enclosure,Output and enclosure,500VDC/100MΩ | |||||||||||
| Working temperature and humidity | -10°C~+60°C(Refer to output derating curve),20%~90%RH | |||||||||||
| Store temperature and humidity | -20°C~+85°C,10%~95%RH | |||||||||||
| Overall dimension | 195×97×38mm | |||||||||||
| Weight | 0.54Kgs | |||||||||||
| Safety standards | Meet UL 1012 requirement(Not apply for the mark) | |||||||||||
| EMC standards | ………… | |||||||||||
| Note | ||||||||||||
| 1.The testing condition for the paramenter above is ,230VAC input,rated load,25°C70% RH.Humidity. | ||||||||||||
| 2.Error.include the setting error,line stability and load stability.(Note,5). | ||||||||||||
| 3.Wave test:adopting "A12"double wire for 20MHz,and 0.1UF&47UF capacitor short-circuit for interrupting. | ||||||||||||
| 4.Inlet voltage stability test,when is over load,the lowest voltage of inlet is up to the highest voltage. | ||||||||||||
| 5.Load stability test:the load is from 0% to 100%. | ||||||||||||
| 6.Total output canbe maximum Current,total load can not exceed the maximum output power | ||||||||||||
Product Picture
PS: If you can't find the exact type of your product.Please don't rush to go away.Contact me and your questions will be replied ASAP.Thank you for your time.